- Place of Origin: Guangdong, China (Mainland)
- Brand Name: reci
- Model Number: reci Z4 100W
- power: 100w
- peak power: 130w
- length: 1400mm
- diameter: 80mm
- worktime: 10000hours
- warranty: yes
- application: co2 laser engraving and cutting machine
Packaging & Delivery
|Packaging Details:||packed in Wood case and Carton box ,the dimension depend on the quantity and the model|
|Delivery Detail:||within 3days afrer payment|
Specificationsco2 reci laser tube Z4 100w
Peak power: 100w
2014new released- Zseries
Reci -co2 laser tube -technical parameters
Match Reci Laser power supply :
- 1. Long life span
It has been proved by experiment that our product can last 10000 hours if the user follow the operation instruction and no physical damage happen . Provides 300 days warranty period.
High quality of laser beam and high power
Same dimension more power
Cutting speech of the machine will be doubled by using Reci tube in comparison to other tube
The output model of W series tube is guaranteed not too be changed in the whole lifespan and power attenuation can be controlled within 10%
1.Small size & good model
The product is featured as small size and good model, higher power rate compared with the laser tube of similar length and longer service time.
Z2 is suitable for laser marking, laser cutting and laser engraving
Z4 is used for the cutting of leather, cloth and processing of lampshade and handicraft.
Z6 is suitable for the cutting of knife mold machine and thick acrylic sheet.
Z8 is which is suitable for the cutting of thin metal plate.
1. 1.Installation Requirement
Make sure to follow the operation instruction of model Z4 as shown in the illustration. The dedicated
power DY13 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv).
It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage.
2. 2.Operation conditions
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃The operating environment: temperature 2-40℃; humidity 10-60%The working current: test current is 30mA. Maximum working current is 30mA. The running current
must be kept below 28mA. The life span can reach 10,000 hours if the current is kept below 26mA.
The ammeter must be connected to the negative electrode of laser tube.When it is working under over-high current for long term, the negative pole will appear brown yellow, and the life span will be
shortened rapidly.To protect dust from going into the insulation sheath, please wrap it with plastic film.
3. 3.Working Performance
Cutting function.Engraving function: Very good. When the working current is 4mA and the tube is in the
state of preionization, the laser can be used for high-frequency impulse engraving.
4. 4.Key Notes
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise
the output power will be seriously affected. The followings are the designated methods to clean up
pollution in the exterior surface of window mirror: 1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon
with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window
from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved,
otherwise the out power will be declined, even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.
5. 5.Safety The laser beam is invisible light. Please wear protective glasses when debugging the laser.
The positive pole is in high voltage. Pay attention to the security marks.
6.Storage and Transportation Requirement
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way. Important notes: it is requested to use adhesive tape to
cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation.
The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting
mirror must be 50 mm wider.
7. 7.Tubes operated in wrong way are not guaranteed by Manufacturer.
All Laser tube will be packed in Wood case and Carton box avoiding to be damaged during shipping and we will make sure the best & high-quality products for you.
The package size :
Generally , we ship out the parcel within 3 days after your payment , but We will ship out package by other Express in case quoted Express can’t reach your shipping address.
If you want us to do shipment to your clients, please leave messages when you make order. we will ship the parcel according your requirement.
Anyway, if you order more tubes,and the volume is very large, and we can also ship them it by Sea.
We accept online payment also including Wester Union, Money Gram, T/T etc.