- Place of Origin: Guangdong, China (Mainland)
- Brand Name: RECI
- Model Number: DY10 DY13 DY20
- MODEL: DY 10 DY13 DY20
- Max output Voltage: 35kv 40 kv 50kv
- Brand name: RECI
- current: 5A 8A 10A
- Max Output current: 24 28 35mA
- quality: high
- apply to: reci tube for co2 laser machine
- AC Frequency: 47-440 Hz
- warranty: 1 year
- Power: 80w 100w 1300w -150w
Packaging & Delivery
|Packaging Details:||standard carton box|
|Delivery Detail:||within 2 days after your payment|
Specifications1 Reci brand power supply for reci tube
2.DY10 DY13 DY20 for z2 z4 z6 z8
3.hot quality best seller . warranty for 1 year
Reci Power Supply DY10
for W2 Z2 80w 90w reci co2 laser tube
Reci Power Supply DY13 for W4 Z4 100-130w reci co2 laser tube
Reci Power Supply DY20
for W8 Z6 130-150w reci co2 laser tube
4.10000 hours working time
Mark & model :
HY-DY10 DY13 DY20 are featured as small size, quick response, which is suitable for Reci W2 & Z2 w4 z4 w6 z6 w8 z8 laser tube
Co2 power supply type
Match laser tube
Z6 Z8 &W6 Z8
1.The shape of this power supply is thin which is specially designed for special laser tube. The power supply makes laser tube output larger and more stable.
2. Quick Response: It can enlarge laser power and prolong laser tube’s service life.
3. Easy Control: The start and stop of laser can be easily controlled by TTL level.
4. This power supply has output open circuit protection.
5. This power supply has TTL signal indication, water Through signal indication and laser output indication.
6.This power supply has the BUTTON to test it work properly.
- 7. Application: Sculpture and cut acrylic, fabric, double color sheet and rubber, etc
AC220VorAC110V( The order should be especially instructions )
Max Input Power
Max Input current
Max output Voltage
Max Output current
equal or more than 90percent ( load down )
equal or more than10000h
equal or less than 1mS( the time from output of switch signal to 90 percent of initial setting current )
Input-Output ,input-machine hull :AC1500V 10mA 60s; output cathode and machine hull connection
Work temperature (-10~40) , Relative humidity :equal or less than 90percent
The force air cooling
Power Supply Instruction
I. Instruction for sub-connection wire of the control end
1 2 3 4 5 6
5V TH TL WP G IN
1) Footer 1 is 5V power supply. (Not needed when connecting the cardinal plate. It is used when regulating
the power with potentiometer, and the 5V current should be less than 10 mA.
2) TH. TL refers to high and low power level respectively, and WP refers to water
3) Footer 5 G refers to ground, and 6 refers to input end.
4) When connecting the control plate, connect the light signal with footer2 in
5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K.
6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3,
5 are connected to switch), the potentiometer center is connected with 6 IN, and
the two other ends are connected to 5V and ground (1 and 5) respectively.
7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in
8) It is not proposed to control laser power with high
frequency modulation, because it will have impact on the service life of the
9) The model is applicable to W4 laser, it is necessary to regulate and use the
current according to the laser instructions.
II.Instruction for power wire
footer 2 footer3
AC 220V 50HZ 10A
Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation.
III. Instruction for laser connection wire
1) The positive red-line with high voltage is connected to the laser tail
2) The negative white-line is connected to laser output window
IV. Current limitation
To limit the working current, the potentiometer (lies in the underside of the power supply) should be rotated in counterclockwise (please refer to the schematic diagram in our website: www.recilaser.com). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery.
V. Linear scale between input signal and the output current
Turn around the potentiometer, the linear scale will be changed: for example, when the input signal is 0-5V, the output current is 0-40mA.Or when the input signal is 0-2V, the output signal is 0-40mA.
Note: when the potentiometer is turned down too much, the real output current will be brought down by the same input signal.
VI. Using current
The use standard for our power supply is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply, the effection is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no effection on the lifespan of the laser if only the current provided by the power supply is not over the current limitation.
All Laser power will be packed in Carton box avoiding to be damaged during the shipping and we will make sure the best and high-quality products for you.
1.1.generally, All the items are only shipped after full payment is cleared ,we deliver the parcel in 2~4days after your payment online ,
2.2.We will deliver the parcel by other Express in case quoted Express can’t reach your shipping address.
3.We will ship to the address which you leave in Aliexpress , when you want to change address ,please inform us before the shipment , otherwise we are not responsible for wrong or undeliverable address